hey all,
i finally got my ms pinky setup going, i have the U46DJ and everything seemed easy enough to get going. However i have a massive error metric, ranging between 1 to 3. I have read glitterbugs earlier thread about the problems with inputs 3 and 4's lack of gain control.
however the problem is on both channels, . .i have gone through the wiring to check its all correct and made sure my control panel is in order.......
I think the main answer to my problem is my needles.... i have the basic stanton carts on their and they are getting very old and have been through much punishment . . .
would this be the reason for such high error readings???
If so, which would be the better choice for ms pinky. i would probably be looking at the shure m447 with its high output and reasonable price . . . i see many others in the forum use it ...
any thoughts. . . .
ms pinky workin.. but error metric!!!
-
- Site Admin
- Posts:1093
- Joined:Mon Jun 07, 2004 9:17 pm
New needles are in order, but also proper U46DJ settings
Your worn and dirty needles could definitely drive the error metrics up to an unworkable level. But just as likely is that you've got something still not set just right:
1) What position are those little switches in on the front panel of the U46DJ box? If your turntable does not have line-level output, then you need to make sure these switches are in the "phono" position...
2) Again you should open up the U46DJ control panel app and double check that you have set the gains on input channels 1&2 to their minimum level.
Unfortunately, those Ego Systems buffoons didn't even provide a control panel app for OSX users... so if you're on a Mac, my recommendation is actually get with a friend who has a PC and get them to let you install the U46DJ control panel app on their machine so you can use it to adjust the input gain settings at least on channels 1&2 (better than having no control at all).
3) And please BOMBARD ESI-PRO.COM and Ego Systems support lines with DEMANDS FOR FIXED DRIVERS!! Those nincompoops owe us properly working drivers (at the very least) for all the support we give them. There's just no excuse for them not including gain controls on input channels 3&4. Doh!!
1) What position are those little switches in on the front panel of the U46DJ box? If your turntable does not have line-level output, then you need to make sure these switches are in the "phono" position...
2) Again you should open up the U46DJ control panel app and double check that you have set the gains on input channels 1&2 to their minimum level.
Unfortunately, those Ego Systems buffoons didn't even provide a control panel app for OSX users... so if you're on a Mac, my recommendation is actually get with a friend who has a PC and get them to let you install the U46DJ control panel app on their machine so you can use it to adjust the input gain settings at least on channels 1&2 (better than having no control at all).
3) And please BOMBARD ESI-PRO.COM and Ego Systems support lines with DEMANDS FOR FIXED DRIVERS!! Those nincompoops owe us properly working drivers (at the very least) for all the support we give them. There's just no excuse for them not including gain controls on input channels 3&4. Doh!!
hey pinkstah,
thanks for the reply
yes, the phono switches are set to the right place and the input channel is down ( i have also muted the monitor channels, is this corect).... and i am already on a PC
i am hoping to test it with some different needles, so i will get back to you on that . . .
is there anything else that can cause such an error metric.....?
and..
your damn right right about the ego systems and will be sending them a message
cheers
thanks for the reply
yes, the phono switches are set to the right place and the input channel is down ( i have also muted the monitor channels, is this corect).... and i am already on a PC
i am hoping to test it with some different needles, so i will get back to you on that . . .
is there anything else that can cause such an error metric.....?
and..
your damn right right about the ego systems and will be sending them a message
cheers
-
- Site Admin
- Posts:1093
- Joined:Mon Jun 07, 2004 9:17 pm
M44-7's rule!
Glad to hear it. M44-7's rule!!
-
- Site Admin
- Posts:1093
- Joined:Mon Jun 07, 2004 9:17 pm
U46DJ Channels 3&4
Echo that. When I'm using the U46DJ, the error metric on my channels 3&4 is around 0.35 - 0.45. In that range, position information can still be decoded just fine, but it's indicative of noise in the signal introduced by the signal being clipped on input.